Epson Stylus Photo 720 Service Manual Download Page 56

Page: 56 / 154

EPSON Stylus Photo 720 / EPSON Stylus Photo EX3

Revision A

Troubleshooting

Unit Level Troubleshooting

3.2.4 Printer does not feed paper correctly

Flowchart 3-1.

3.2.5 Control panel operation is abnormal

Flowchart 3-1.

START

Paper

loaded correctly

in ASF?

Set the paper correctly.

Do PF roller

and platen

rotate?

Is the

PF motor

running?

YES

Check the PF motor.

No problem = replace the

MAIN board.

YES

Remove any obstruction in

the paper path if there is

any.

Clean the roller of

paper path.

Is the

problem

solved?

Refer to “Unit Repair

(Printer Mechanism)”.

YES

END

Control

panel connected

correctly?

START

Connect the

control panel

correctly.

YES

END

Is the

problem

solved?

Replace the

control panel.

Replace the

MAIN Board.

Control

panel connected

correctly?

Summary of Contents for Stylus Photo 720



























































































































































Search results

Summary of Contents for Stylus Photo 720

Reviews:

Related manuals for Stylus Photo 720

Brands by name

Popular brands

Epson Stylus Photo 720, Service Manual

Search results

Summary of Contents for Stylus Photo 720

Reviews:

Related manuals for Stylus Photo 720

Brands by name

Popular brands