Epson Stylus Photo 720 Service Manual Download Page 68

Page: 68 / 154

EPSON Stylus Photo 720 / EPSON Stylus Photo EX3

Revision A

Disassembly and Assembly

Disassembly

4.2.1 Housing Removal

Since this printer has no lower Housing, the Printer Mechanism is exposed just by
removing the Housing.

Open the Printer Cover and set the PG Adjust Lever to (+) position.

Remove 4 screws and remove the Housing.

Figure 4-2. Housing Removal

C H E C K

P O I N T

When removing the Housing, be sure to keep the Housing out of
carriage: Pull the Housing toward the printer front side and lift it
upward.

When installing the Housing, be careful not to pinch the cable with
the screw at the rear side of the Housing.
Make sure the Head FFC is set properly inside the rail on the back of
the Housing.

Housing

Summary of Contents for Stylus Photo 720



























































































































































Search results

Summary of Contents for Stylus Photo 720

Reviews:

Related manuals for Stylus Photo 720

Brands by name

Popular brands

Epson Stylus Photo 720, Service Manual

Search results

Summary of Contents for Stylus Photo 720

Reviews:

Related manuals for Stylus Photo 720

Brands by name

Popular brands