Epson S1C17F13 Technical Manual Download Page 75

Page: 75 / 247

7 WATCHDOG TIMER (WDT)

S1C17F13 TeChniCal Manual

Seiko epson Corporation

7-3

(Rev. 1.0)

Control Registers

7.4

WDT Clock Control Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

WDTCLK

15–9 –

0x00

–

DBRUN

R/WP

7–6 –

0x0

–

5–4 CLKDIV[1:0]

0x0

R/WP

3–2 –

0x0

–

1–0 CLKSRC[1:0]

0x0

R/WP

Bits 15–9 Reserved

Bit 8

DBRun

This bit sets whether the WDT operating clock is supplied in DEBUG mode or not.

1 (R/WP): Clock supplied in DEBUG mode

0 (R/WP): No clock supplied in DEBUG mode

Bits 7–6

Reserved

Bits 5–4

ClKDiV[1:0]

These bits select the division ratio of the WDT operating clock (counter clock). The clock frequency
should be set to around 256 Hz.

Bits 3–2

Reserved

Bits 1–0

ClKSRC[1:0]

These bits select the clock source of WDT.

4.1 Clock Source and Division Ratio Settings

Table 7.

WDTCLK.

CLKDIV[1:0] bits

WDTCLK.CLKSRC[1:0] bits

0x0

0x1

0x2

0x3

OSC3B

OSC1

OSC3A

EXOSC

0x3

1/65,536

1/128

1/65,536

1/1

0x2

1/32,768

0x1

1/16,384

0x0

1/8,192

(Note) The oscillation circuits/external input that are not supported in this IC cannot be

selected as the clock source.

WDT Control Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

WDTCTL

15–10 –

0x00

–

NMIXRST

R/WP

STATNMI

7–5 –

0x0

–

WDTCNTRST

Always read as 0.

3–0 WDTRUN[3:0]

0xa

R/WP –

Bits 15–10 Reserved

Bit 9

nMiXRST

This bit sets the WDT operating mode.

1 (R/WP): NMI mode

0 (R/WP): Reset mode

This bit is used to select whether an NMI signal or a reset signal is output when WDT has not been
reset within the NMI/reset generation cycle.

Summary of Contents for S1C17F13
























































































































































































































































Search results

Summary of Contents for S1C17F13

Reviews:

Brands by name

Popular brands

Epson S1C17F13, Technical Manual

Search results

Summary of Contents for S1C17F13

Reviews:

Brands by name

Popular brands