Epson S1C17F13 Technical Manual Download Page 170

Page: 170 / 247

16 16-BIT PWM TIMERS (T16A3)

S1C17F13 TeChniCal Manual

Seiko epson Corporation

16-15

(Rev. 1.0)

6.5 Capture A Trigger Edge Selection

Table 16.

T16A

CCCTL.CAPATRG[1:0] bits

Trigger edge

0x3

Falling edge and rising edge

0x2

Falling edge

0x1

Rising edge

0x0

Not triggered

The T16A

CCCTL.CAPATRG[1:0] bits are control bits for capture mode and are ineffective in com-

parator mode.

Bits 5–4

TOuTaMD[1:0]

These bits configure how the TOUTA signal waveform (TOUTA

output) is changed by the compare

A and compare B signals. These bits are also used to turn the TOUTA output on and off.

6.6 TOUTA Signal Generation Mode

Table 16.

T16A

CCCTL.

TOUTAMD[1:0] bits

When compare A occurs When compare B occurs

0x3

No change

Toggle

0x2

Toggle

No change

0x1

Rise

Fall

0x0

Disable output

The T16A

CCCTL.TOUTAMD[1:0] bits are control bits for comparator mode and are ineffective in

capture mode.

Bits 3–2

Reserved

Bit 1

TOuTainV

This bit selects the TOUTA signal (TOUTA

output) polarity.

1 (R/W): Inverted (active low)

0 (R/W): Normal (active high)

The T16A

CCCTL.TOUTAINV bit is a control bit for comparator mode and are ineffective in capture

mode.

Bit 0

CCaMD

This bit selects the T16A

CCA register operating mode.

1 (R/W): Capture mode (T16A

CCA register = capture A register)

0 (R/W): Comparator mode (T16A

CCA register = compare A register)

T16a3 Comparator/Capture Ch.

a Data Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

T16A

CCA

15–0 CCA[15:0]

0x0000

R/W –

Bits 15–0 CCa[15:0]

In comparator mode (T16A

CCCTL.CCAMD bit = 0), this register is configured as the compare A

In capture mode (T16A

CCCTL.CCAMD bit = 1), this register is configured as the capture A register

and the counter value captured by the external trigger signal (CAPA

) is loaded.

Note: When writing data to the T16A

CCA register successively, data should be written at intervals of

one or more T16A3 count clock cycles.

T16a3 Comparator/Capture Ch.

B Data Register

Register name

Bit

Bit name

Initial

Reset

R/W

Remarks

T16A

CCB

15–0 CCB[15:0]

0x0000

R/W –

Bits 15–0 CCB[15:0]

In comparator mode (T16A

CCCTL.CCBMD bit = 0), this register is configured as the compare B

Summary of Contents for S1C17F13
























































































































































































































































Search results

Summary of Contents for S1C17F13

Reviews:

Related manuals for S1C17F13

Brands by name

Popular brands

Epson S1C17F13, Technical Manual

Search results

Summary of Contents for S1C17F13

Reviews:

Related manuals for S1C17F13

Brands by name

Popular brands