Epson LX-1170 Service Manual Download

Page: 86 / 129

LX-300+/1170

Revision C

Disassembly and Assembly

Remove the harness from the sensor (blue).

Figure4-21. Release Lever Position Sensor Removal

4.2.7.10 PF Motor Assembly Removal

Remove the printer mechanism. (See 4.2.3 "Printer Mechanism Removal".)

Remove the platen grounding wire from the platen.

Remove 1 screw (C.B.P., Tite, 3x10 F/ZN; Torque 0.59-0.78 N.M.) securing the PF
motor assembly to the right frame.

Remove 1 hook at the right frame securing the PF motor assembly to the right frame
and remove the PF motor assembly.

Figure4-22. PF Motor Assembly Removal

C A U T I O N

When installing the release lever position sensor, be sure to insert it
between the release lever and the right frame.

Release lever position sensor (blue)

C H E C K

P O I N T

When installing the PF motor assembly to the right frame, be careful
to align the position marking pin and motor bracket position marking
hole.

Platen grounding wire

PF motor assembly

C.B.P., Tite, 3x10 F/ZN

Hook at the right frame

Position marking pin

Summary of Contents for LX-1170


































































































































Search results

Summary of Contents for LX-1170

Reviews:

Related manuals for LX-1170

Brands by name

Popular brands

Epson LX-1170, Service Manual

Search results

Summary of Contents for LX-1170

Reviews:

Related manuals for LX-1170

Brands by name

Popular brands