Epson LX-1170 Service Manual Download

Page: 14 / 129

LX-300+/1170

Revision C

PRODUCT DESCRIPTION

SPECIFICATIONS

1.2.2 Paper Feeding

Feeding method:

Friction feed (rear)
Push tractor feed (rear)
Push and Pull tractor feed (rear)
Pull tractor feed (rear, bottom)

Feeder:

Rear push tractor, CSF single-bin (Option),
Pull tractor (Option) and Roll paper holder (Option)

Paper path:

Manual insertion

Rear in, top out

CSF

Rear in, top out

Push Tractor

Rear in, top out

Pull Tractor

Rear or bottom in, top out

Line spacing:

4.23mm (1/6 inch) or programmable in increments of ;
LX-300+: 0.118mm(1/216 inch)
LX-1170: 0.059mm(1/432 inch)

Feed speed:

4.23mm (1/6 inch feed)

LX-300+

88msec

LX-1170

63msec

Continuous feed

0.76MPS (m/sec)
[3.0 IPS (inches/sec)]

Input Data Buffer:

8 Kbyte

Release lever:
The release lever must be set according to the following table;

Paper thickness lever:
The paper thickness lever must be set at the proper position as shown below.

Table 1-4. Release Lever

Lever position

Paper path/ Feeder

Paper/ Media

Friction

Manual insertion (rear)

Cut sheet (Single sheet and Multi part)

Envelop

CSF single-bin

Cut sheet (Single sheet)

Roll paper holder feed (rear)

Roll paper

Tractor

Push tractor feed (rear)

Continuous paper (Single sheet and
Multi part)

Push and Pull tractor feed (rear)

Continuous paper (Single sheet and
Multi part)

Pull tractor feed (rear)

Continuous paper (Single sheet and
Multi part)

Pull tractor feed (bottom)

Continuous paper (Single sheet and
Multi part)

Labels

Table 1-5. Paper Thickness Lever

LX-300+

LX-1170

Lever

position

Paper thickness

(inch)

Paper

thickness

(mm)

Paper thickness

(inch)

Paper

thickness

(mm)

Min.

Max.

Min.

Max.

-1

(0.0024)

(0.0071)

over 0.06

up to 0.18

(0.0024)

(0.0071)

over 0.06

up to 0.18

(0.0071)

(0.0102)

over 0.18

up to 0.26

(0.0102)

(0.0130)

over 0.26

up to 0.33

(0.0071)

(0.0102)

over 0.18

up to 0.26

(0.0130)

(0.0154)

over 0.33

up to 0.39

Table 1-4. Release Lever

Lever position

Paper path/ Feeder

Paper/ Media

Summary of Contents for LX-1170


































































































































Search results

Summary of Contents for LX-1170

Reviews:

Related manuals for LX-1170

Brands by name

Popular brands

Epson LX-1170, Service Manual

Search results

Summary of Contents for LX-1170

Reviews:

Related manuals for LX-1170

Brands by name

Popular brands