Epson LX-1170 Service Manual Download

Page: 100 / 129

Product Name

Revision C

Maintenance

Figure 6-1. Left Frame Assembly

Figure 6-2. Teeth of Gears at the Left Frame

Figure 6-3. Shafts at the Right Frame Assembly

Figure 6-4. Release Lever

Lubricate G-26 on the 3 shafts and 1 boss
of the left frame.
G-26, 1/2 grain of rice

Lubricate G-26 on the shaft of the RD
ratchet.
G-26, 1 grain of rice

Planetary lever assy.

Combination Gear 5.1, 16.2

Spur Gear, 13.2

RD ratchet

Driven pulley assy.

Lubrication Points

Spur Gear, 13.2

RD ratchet shaft

Lubricate G-26 on teeth of gears.
G-26, 1/2 grain of rice

Lubricate G-26 at 3 places on 3 shafts at
the right frame.

Shafts at the right frame assembly:
G-26, 1 grain of rice

Lubricate G-26 at 2 places on inside of cam
at slope surface of the release lever.

Release lever:
G-26, 1 grain of rice

Summary of Contents for LX-1170


































































































































Search results

Summary of Contents for LX-1170

Reviews:

Related manuals for LX-1170

Brands by name

Popular brands

Epson LX-1170, Service Manual

Search results

Summary of Contents for LX-1170

Reviews:

Related manuals for LX-1170

Brands by name

Popular brands