Epson LX-1170 Service Manual Download

Page: 79 / 129

LX-300+/1170

Revision C

Disassembly and Assembly

Figure4-7. C294MAIN Board Assembly Removal

4.2.6 C294 Power Supply Board Assembly Removal

Remove the upper housing. (See 4.2.2 "Upper Housing Removal".)

Remove the printer mechanism. (See 4.2.3 "Printer Mechanism Removal".)

LX-1170: Remove 1 screw(C.B.P., Tite, 3x10 F/ZN;Torque 0.78-0.98 N.M.)

and the left grounding plate.

LX-1170: Remove 1 screw (C.B(O), Screw, 4x8, F/ZN; Torque 0.98-1.18 N.M.)

and the grounding cable.

Figure 4-8. Ground Plate and Cable Removal (LX-1170)

Remove the power cable (CN1) connecting to the Power Supply board assembly.
Remove the power switch from the lower housing.

Remove the harness connecting the Power Supply board assembly to the main board
assembly. (CN8 of the main board assembly)
Press one edge of CN8 in order to remove or install the harness.

Remove 4 screws (C.B.P., Tite, 3x10 F/ZN; Torque 0.78-0.98 N.M.) securing the
Power Supply board assembly to the lower housing.

Remove the Power Supply board assembly.

A D J U S T M E N T

R E Q U I R E D

When the main board assembly is replaced, perform destination
setting and Bi-D adjustment.

Main Board Assembly

Hexagon Nut

Lower Shield Plate

C.P., Screw, 3x4 F/ZN

C.B.P., Tite, 3x10 F/ZN

CN8

CN13

CN12

C.B.P., Tite, 3x10 F/ZN

C.B(O), Screw, 4x8 F/ZN

Grounding Plate, Left

Grounding Cable

C.P., Screw, 3x4 F/ZN

Summary of Contents for LX-1170


































































































































Search results

Summary of Contents for LX-1170

Reviews:

Related manuals for LX-1170

Brands by name

Popular brands

Epson LX-1170, Service Manual

Search results

Summary of Contents for LX-1170

Reviews:

Related manuals for LX-1170

Brands by name

Popular brands