Epson LX-1170 Service Manual Download | Manualshive

Page: 52 / 129

background image

LX-300+/1170

Revision C

Operating Principles

Printer Mechanism

52

COLOR MECHANISM INITIALIZATION

The printer mechanism initializes when the power is applied or when recovering from the
energy saving mode.

o

Color mechanism initialization
Color mechanism initialization shifts color mechanism for the black ink area to be
at the home position. Color mechanism initialization shifts the carriage at the same
time to prevent the ribbon from hanging on the printhead.
When the buffer is cleared or when the printer is under the pause condition, the
color mechanism initializes and waits for the next printing command.

2.2.4 Platen Gap Adjustment Mechanism

This mechanism is to adjust the distance between the platen and the printhead (platen gap)
according to the paper thickness.

The following is the components of the LX-300+/1170 platen gap adjustment mechanism
and its explanation. (Refer to Refer to Figure 2-5.)

o

Carriage:

Mounts the printhead.

o

Carriage guide shaft:

Shifts the carriage horizontally.

o

Adjust lever and Parallelism adjust bushing:
Installed at the both ends of the carriage guide shaft

o

Platen gap detector (PG_SW)

Carriage guide shaft is eccentric toward the adjust lever rotating center. Due to this, when
rotating the adjustment lever back and forth, the printhead shifts toward and against the
platen to adjust the platen gap. When printing on thick paper such as postcards and
envelops, set the adjust lever over the 1st level. PG detector shifts the printer to the copy
mode from the printing mode. Printing speed will be lowered but it prevents wire from
breaking off.

PLATEN GAP (PG_SW) DETECTOR

The following is PG_SW specification.

Figure 2-5. Platen Gap Adjustment Mechanism

Table 2-9. PG_SW Detector Specifications

Item

Specification

Method

Mechanical contact method

Switching rate

0.6 to 1.0 mA, 5 VD±5%

Switching mode

• PG=0: close

• PG=0-4: open

Adjust lever

Carriage guide shaft

Carriage

Parallelism adjust

bushing

Printer mechanism

Parallelism adjust

bushing

PG_SW

Platen gap

Platen

Carriage guide shaft

Carriage

Printhead

Adjust lever

«
...
50
51
52
53
54
...
»

Summary of Contents for LX-1170


































































































































Reviews:

No comments

Related manuals for LX-1170

Brand: Canon Pages: 11

imageRUNNER ADVANCE 8085

Brand: Canon Pages: 176

Brand: Canon Pages: 85

imageRUNNER 5070

Brand: Canon Pages: 4

imageRUNNER 5570

Brand: Canon Pages: 4

IMAGERUNNER 7095 PRINTER

Brand: Canon Pages: 8

IMAGERUNNER 7105

Brand: Canon Pages: 21

Brand: Canon Pages: 58

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 12

imageRUNNER ADVANCE C2020

Brand: Canon Pages: 68

imageRUNNER ADVANCE 6055

Brand: Canon Pages: 134

Color imageRUNNER LBP5970

Brand: Canon Pages: 67

FAXPHONE L170 - B/W Laser - Copier

Brand: Canon Pages: 12

Brand: Canon Pages: 2

imageRunner 1133

Brand: Canon Pages: 60

Color imageCLASS MF8280Cw

Brand: Canon Pages: 36

Brand: Canon Pages: 104

imagePROGRAF iPF8300

Brand: Canon Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands