Epson ET-14000 Programming Manual Download Page 78

Page: 78 / 82

2016/08/25

Revision: 2

Page:

7.1 Status code

Structure

Item

Byte (Hex)

Value (Hex)

Header

Parameter counter

Parameter

The parameter <Status code> is one byte Binary code that indicates status code as follows.

Status

Status code

In the error state

In the self printing state

In the busy state

In the waiting state

In the idle state

In the cleaning state

In the factory shipment state

In the shutdown state

In the Initial charge state

7.2 Error code

Structure

Item

Byte (Hex)

Value (Hex)

Header

Parameter counter

Parameter

The parameter <Error code> is one byte Binary code that indicates error code as follows.

Error

Error code

Fatal error

Other I/F is selected

Paper jam

Paper out

Ink overflow error

Double Feed Error

Cover Open Error

Maintenance request will be occurred as soon

Summary of Contents for ET-14000



















































































Search results

Summary of Contents for ET-14000

Reviews:

Related manuals for ET-14000

Brands by name

Popular brands

Epson ET-14000, Programming Manual

Search results

Summary of Contents for ET-14000

Reviews:

Related manuals for ET-14000

Brands by name

Popular brands