Epson ET-14000 Programming Manual Download Page 31

Page: 31 / 82

2016/08/25

Revision: 2

Page:

5.1.7 Set absolute horizontal print position ESC $ nL nH

ESC $ nL nH

Ver 1.00

[Name]

Set absolute horizontal print position

[Operation]

[Format]

1BH, 24H, nL, nH

[Range of Definition]

≤

255

≤

127

[Function]

1) The printing position in the positive X direction is set to:

0 <= (256 x nH + nL) x 2880

<= 209.973 mm

(absolute horizontal position setting value)

0 <= (256 x nH + nL) x 2880

<= 23808 inch

(absolute horizontal position setting value)

2880

from the origin (the left margin position) on the X axis of the position management coordinate

system.

If (current left margin po((256 x nH + nL) x (absolute horizontal position setting
value)) is passed the right margin position, then this command is ignored.

[Initial State]

[Related Commands]

[Setting] Commands whose settings are affected by this command.

None

[Setting] Commands that change the effects of this command.

None

[Operation] Commands whose functionality is affected by this command.

None

[Operation] Commands that change the effects of this command.

The “absolute horizontal position setting value” is set by the ESC (U command.

The “absolute horizontal position setting value” is restored to its initial state by the ESC @
and ESC (G commands.

The printer settings are restored to their initial state to by the ESC @ command.

Summary of Contents for ET-14000



















































































Search results

Summary of Contents for ET-14000

Reviews:

Related manuals for ET-14000

Brands by name

Popular brands

Epson ET-14000, Programming Manual

Search results

Summary of Contents for ET-14000

Reviews:

Related manuals for ET-14000

Brands by name

Popular brands