Epson ET-14000 Programming Manual Download Page 26

Page: 26 / 82

2016/08/25

Revision: 2

Page:

5.1.2 Initialize printer ESC @

ESC @

Ver 1.00

[Name]

Initialize printer

[Setting]

[Format]

1BH, 40H

[Range of Definition]

[Function]

1) The various settings are returned to their initial values.

2) The Y axis origin of the page management coordinate system and the position management

coordinate system are set to the current printing position on the Y axis.

3) The present printing position on the X axis is set to the origin upon the X axis.

4) Text mode printing is selected.

[Initial State]

[Related Commands]

[Setting] Commands whose settings are affected by this command.

The settings for all commands are returned to their initial states.

[Setting] Commands that change the effects of this command.

None

[Operation] Commands whose functionality is affected by this command.

None

[Operation] Commands that change the effects of this command.

None

Summary of Contents for ET-14000



















































































Search results

Summary of Contents for ET-14000

Reviews:

Related manuals for ET-14000

Brands by name

Popular brands

Epson ET-14000, Programming Manual

Search results

Summary of Contents for ET-14000

Reviews:

Related manuals for ET-14000

Brands by name

Popular brands