Epson ET-14000 Programming Manual Download Page 57

Page: 57 / 82

2016/08/25

Revision: 2

Page:

5.1.31 Select printing color ESC r n

ESC r n

Ver 1.00

[Name]

Select printing color

[Setting]

[Format]

1BH, 72H, n

[Range of Definition]

00H

≤

04H

[Function]

1) The printing color is selected according to the value of n, as follows:

if n=0:    black
if n=1:    magenta
if n=2:    cyan
if n=4:    yellow

2) If n has a value other than the above, this command is ignored.

[Initial State]

Black selected.

[Related Commands]

[Setting] Commands whose settings are affected by this command.

None

[Setting] Commands that change the effects of this command.

The ESC @ command selects black.

[Operation] Commands whose functionality is affected by this command.

None

[Operation] Commands that change the effects of this command.

None

Summary of Contents for ET-14000



















































































Search results

Summary of Contents for ET-14000

Reviews:

Related manuals for ET-14000

Brands by name

Popular brands

Epson ET-14000, Programming Manual

Search results

Summary of Contents for ET-14000

Reviews:

Related manuals for ET-14000

Brands by name

Popular brands