manualshive.com logo in svg

Epson Elp-3500, Service Manual, Page: 82 / 114

Share
Download
Epson Elp-3500 Service Manual Download Page 82

EPSON ELP-3500 Service Manual

4-5

Figure 4-4.

Video Display Mode

START

(Display Mode is OK.)

Check the projector with

a PC. Is PC input OK?

Reconnect CN100 and

CN101 on the main board.

Is PC input OK now?

Replace the main board.

Is PC input OK now?

Replace the driver

board.

NO

NO

NO

YES

YES

YES

NO

NO

NO

NO

NO

NO

NO

Does the Brightness

control work with the

video menu?

Does the Brightness

control work with the

video menu now?

Replace the driver

board.

Replace the main

board.

Go to “Audio Mode.”

Is loop throughput

OK?

Replace the main

board.

Is loop throughput

OK now?

Replace the driver board.

YES

YES

YES

YES

YES

YES

YES

Replace the interface

unit.

Is PC input OK now?

NO

YES

Is video input OK?

Replace the main

board.

Is video input OK

now?

Replace the driver

board.

Is video input OK

now?

Replace the

interface unit.

Summary of Contents for Elp-3500



















































































































Reviews:

No comments