manualshive.com logo in svg

Epson Elp-3500, Service Manual, Page: 81 / 114

Share
Download
Epson Elp-3500 Service Manual Download Page 81

EPSON ELP-3500 Service Manual

4-4

Figure 4-3.

DISPLAY MODE

START

(System Init is OK.)

Go to

“Video

Display

Mode.”

Does the lamp light?

Replace the lamp.

Does the lamp light now?

Replace the driver board.

Check fuses F600 to F602

on the driver board. If blown

replace driver board.

Does the screen appear

now?

NO

NO

NO

NO

NO

NO

NO

Does the screen appear?

Check CN850, 900, 950

connections on the driver board.

Does the screen appear

now?

Reconnect the main board

and driver board.

NO

Does the screen appear

now?

Replace F600 on the driver

board.

Does the menu key work

normally?

(Menu screen appears.)

Does the menu key work

normally now?

Replace the main board.

Replace the driver board.

YES

YES

YES

YES

YES

YES

YES

Replace the driver board.

Does the lamp light now?

Replace the power supply

NO

YES

YES

YES

NO

Does the screen appear

now?

Replace the safety switch on

the lamp’s outer housing.

Does the lamp light now?

NO

YES

Does screen appear now?

Replace the main board.

NO

YES

Summary of Contents for Elp-3500



















































































































Reviews:

No comments