manualshive.com logo in svg

Epson Elp-3500, Service Manual, Page: 80 / 114

Share
Download
Epson Elp-3500 Service Manual Download Page 80

EPSON ELP-3500 Service Manual

4-3

YES

NO

Figure 4-2.

SYSTEM INITIALIZATION

START

Turn on power.

Does the projector have power

(POWER LED is lit)?

Reconnect the cable between

the control panel and main

board.

Does the POWER LED

light now?

Check fuses FU500 to 505 on

the main board, and if bad,

replace the main board.

Does the POWER LED

light now?

Replace the control panel.

Does the POWER LED

light now?

Replace the ROM (IC304)

on the main board.

Replace the power supply.

Does the POWER LED

light now?

YES

YES

NO

NO

NO

NO

NO

NO

NO

NO

NO

NO

NO

Go to

“Display

Mode.”

Do the fans work?

Check CN502 and CN503

connection on the main board

and on the driver board.

Do the fans work now?

If fuse FU501 is blown on the

main board, replace

the main board.

Do the fans work now?

Replace fans.

Is lamp indicator

normal?

Check CN505 connection on

the main board. Is it OK?

Is lamp indicator normal

now?

Replace the driver board.

Is lamp indicator normal

now?

Replace the main board.

YES

YES

YES

YES

YES

YES

YES

YES

YES

NO

NO

Do fans work now?

Replace the main board.

After you replace the main

board, does the POWER

LED light?

NO

YES

Summary of Contents for Elp-3500



















































































































Reviews:

No comments