manualshive.com logo in svg

Epson Elp-3500, Service Manual, Page: 55 / 114

Share
Download
Epson Elp-3500 Service Manual Download Page 55

EPSON ELP-3500 Service Manual

3-4

3.2.1  Removing the Lamp Inner Housing

Lamp Cover

Screws

Figure 3-2.

Lamp Inner Housing

Screws

Handle

Figure 3-3.

1.  Remove the lamp cover mounting screws from the main unit bottom plate and

remove the lamp cover.

Screws:

M4x7.5 F/Ni: P/N 1021771
Mounting torque: 4.5 kg cm = 3.9 lb inch

2.  Remove 2 lamp mounting screws from the inner housing.

Screws:

M4x7.5 F/Ni: P/N 1021771
Mounting torque: 4.5 kg cm = 3.9 lb inch

3.  Pull up the handle on the lamp inner housing and remove the lamp unit.

Warning:

1.  The lamp unit is very hot immediately after use and may burn you if handled

carelessly.  Before removing the lamp unit, make sure the temperature of the lamp
inner housing unit has cooled down.

2. When installing the lamp unit, take care not to touch the lamp's reflector with your

hands (to prevent the reflector from being contaminated).

Summary of Contents for Elp-3500



















































































































Reviews:

No comments