manualshive.com logo in svg

Epson Elp-3500, Service Manual, Page: 71 / 114

Share
Download
Epson Elp-3500 Service Manual Download Page 71

EPSON ELP-3500 Service Manual

3-20

3.2.14  Removing the Adjustable Foot Unit

Prerequisite: Complete the steps explained in sections 3.2.1, 3.2.4, 3.2.10, and 3.2.11.

Adjustable

Foot

Foot

Lever

Figure 3-24.

Compression

Spring

Foot
Axis

Foot Lever

Foot

Lever Pin

Figure 3-25.

1. Turn the adjustable foot counterclockwise about 40 times to remove it.
2. While pressing the foot lever, pull the foot axis upward to remove it.
3. Slide the upper side (foot lever side) of the compression spring to remove it.
4. Remove the foot lever pin then remove the foot lever

Caution:

When installing or removing the adjustable foot unit, do not fold or peel the foot seal on
the lower case. Insert the foot lever, then replace the counter spring, and finally insert the
foot axis. When installation is complete, press the foot lever to check whether it makes a
strange noise. If it makes noise, adjust the compression spring to change the contact
point with the foot lever to eliminate the noise.

Summary of Contents for Elp-3500



















































































































Reviews:

No comments