OPTIONAL EQUIPMENT
REV.-A
3.3.1 C80612 CUT-SHEET FEEDER SPECIFICATIONS
This section describes specifications for the C80612 cut-sheet feeder.
3.3.1.1 General Specifications
Hopper Capacity:
For paper weight of:
17 pounds (64 g/m
2
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
185 sheets maximum
24 pounds (90 g/m
2
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100 sheets maximum
NOTE:
If the weight of the paper differs from the above, total thickness of the stack of paper must be less
than 0.59 inches (15 mm).
Stacker Capacity:
17 pounds (64 g/m
2
) paper ................................... 100 sheets maximum
24 pounds (90 g/m*) paper ......... . ........................... 55 sheets maximum
Reliability:
MCBF (Mean Cycles
Between Failures):
100,000 cycles
Environmental Requirements:
Operating temperature range - + 41 to 95°F (+ 5 to 35°C)
Storage temperature range - - 22 to 149°F (- 30 to 65°C)
Operating humidity range - 15% to 80% (with no condensation)
Storage humidity range - 5% to 85% (with no condensation)
3.3.1.2 Paper Specifications
Cut-sheet paper must be new or like new, must not be curled or curved, and must be free of surface and
edge damage.
Paper type and quality:
Plain bond, typewriter, or PPC-quality paper with a minimum wood pulp
content
NOTE:
Paper with higher wood content, very light, and very heavy paper, must be tested operationally
prior to regular use. Paper with a textured embossed, glossy, or hammered surface also must be
tested.
Paper width and length:
Width - 7.17 inches (182 mm) to 8.50 inches (216 mm)
Length - 10.1 inches (257 mm) to 14.3 inches (364 mm)
Paper thickness:
0.0028 inches (0.07 mm) to 0.0039 inches (0.1 mm)
Paper weight:
17 pounds to 24 pounds (64 to 90 g/m
2
)
Angular deviation:
Less than ± 0.02 inches (0.5 mm)
Recommended conditions for paper storage:
Temperature:
+ 64
to 72° F (18 to 22°C)
Humidity:
40%
to 60%
3-6
LQ-510
Summary of Contents for AP-4000
