Epson AN2WA87 Installation Instructions Manual Download Page 2

AN2 Series

Installation Instructions

2

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.

 IMPORTANT SAFETY INSTRUCTIONS

WARNING:

A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION:

A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the
corresponding instructions.

WARNING:

Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty!  It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.

WARNING:

Failure to provide adequate structural strength

for this component can result in serious personal injury or
damage to equipment!  It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a

minimum

 drywall thickness of 1/2" (12.7mm) for

wood and steel stud walls, and NO drywall on concrete walls.

WARNING:

Use this mounting system only for its intended

use as described in these instructions. Do not use
attachments not recommended by the manufacturer.

WARNING:

Never operate this mounting system if it is

damaged. Return the mounting system to a service center for
examination and repair.

WARNING:

Do not use this product outdoors.

IMPORTANT ! :

The AN2 Series includes the AN2 87" and

100" mounts. These mounts are designed to be used

ONLY

with the following Epson projector models:

BrightLink Pro 1430Wi

BrightLink Pro 1420Wi

BrightLink 595Wi

BrightLink 585Wi

IMPORTANT ! :

The AN2 Series systems are designed to be

mounted to:

a bare 8" concrete or 8"x8"x16" concrete block wall;

a 2" x 4"  wood studs (16" on center minimum to 24" on
center maximum) wall with a minimum drywall
thickness of 1/2" (12.7mm);

a 2" x 4"-25ga minimum steel studs (16" on center
minimum to 24" on center maximum) wall with a
minimum drywall thickness of 1/2" (12.7mm).

--SAVE THESE INSTRUCTIONS--

Summary of Contents for AN2WA87





















Reviews: