Epson 5000XB - PowerLite SVGA LCD Projector User Manual Download Page 40

Page: 40 / 124

1 • Installation

2. Connect the main cable. The main cable connects the mouse cable

(needed to use the remote control as a mouse) and serial cable
(needed to use the ELP Link II software) to the projector.

a. Connect the small end of the main cable to the projector’s

Mouse/Com 1 port. (Use the Mouse/Com 2 port if you are
connecting a second computer.)

b. Connect the MAC mouse cable to the mouse terminal on the

other end of the main cable.

c. Connect the mouse connector of the MAC mouse cable to the

mouse port on the back of the PowerBook.

main cable

MAC mouse
cable

MAC serial
cable

pro-ch1.fm Page 22 Friday, November 7, 1997 5:22 PM

Summary of Contents for 5000XB - PowerLite SVGA LCD Projector





























































































































Search results

Summary of Contents for 5000XB - PowerLite SVGA LCD Projector

Reviews:

Brands by name

Popular brands

Epson 5000XB - PowerLite SVGA LCD Projector, User Manual

Search results

Summary of Contents for 5000XB - PowerLite SVGA LCD Projector

Reviews:

Brands by name

Popular brands