Epson 5000XB - PowerLite SVGA LCD Projector User Manual Download Page 26

Page: 26 / 124

1 • Installation

Connecting to a PC Desktop Computer

Before beginning, turn off the projector and computer if they are on.

1. Connect the video cable.

Note:

Computer configurations vary. See your computer manual for

the location of the ports needed to connect your projector.

a. Connect one end of the video cable to the projector’s

Computer In 1 port. (Use the Computer In 2 port if you are
connecting a second computer.)

b. Disconnect the computer monitor cable from the video port

on the back of the computer, and connect the other end of the
video cable to the computer’s video port.

monitor cable

video cable

pro-ch1.fm Page 8 Friday, November 7, 1997 5:22 PM

Summary of Contents for 5000XB - PowerLite SVGA LCD Projector





























































































































Search results

Summary of Contents for 5000XB - PowerLite SVGA LCD Projector

Reviews:

Brands by name

Popular brands

Epson 5000XB - PowerLite SVGA LCD Projector, User Manual

Search results

Summary of Contents for 5000XB - PowerLite SVGA LCD Projector

Reviews:

Brands by name

Popular brands