EPS 1001905 Operation And Maintenance Manual Download Page 22

22

22

Troubleshooting

Steadypres VSD

PROBLEM

The pump is not feed

Message

Cause

Intervention

none

Interruption of power supply

Replace the power supply

none

Burned fuses

Substitute the fuses

none

Intervention of the line protections

Check the correct protecttions setting

INPUT ERROR

(only mod. T/T) - connections LINE and MOTOR 

were reversed

Check the connections LINE and MOTOR and 

connect correctly

PROBLEM

The current circuit breaker has tripped to 

protect the DGBOX power line

Message

Cause

Intervention

none

The residual current circuit breaker is 

inadequate for inverter supply

Replace the residual current circuit breaker with 

a model suitable for the pulsating components 

and in direct current (class A)

PROBLEM

The pump fails to start

Message

Cause

Intervention

OFF

The pump is out of service

(placed manually out of service)

Put the pump back into service by 

pushing START

PROBLEM

The pump stopped and fails to re-start

Message

Cause

Intervention

OVER CURRENT

overcurrent absorption compared to set value 

(parameter A in BASE PARAMETER)

•  check the correct current setting

•  check the power voltage under load at pump 

terminals (min -15%)

•  make sure the motor pump is turning freely 

and is not braked

•  check the correct direction of rotation

•  check the correct sizing of the wires

CURRENT LIMIT

Serious overcurrent absorption which inverter 

cannot cope with

Make sure the motor pump is not blocked, 

reduce the motor acceleration by means of the 

ACCELERATION parameter.

DRY RUNNING

(DRY RUNNING PF)

•  Lack of water at suction

•  pump not primed

•  suction blocked

•  wrong direction of motor rotation

•  Check correct suction conditions

•  prime the pump

•  check the suction piping

•  check the correct direction of motor rotation

LOW PRESS

The system does not reach the minimum 

pressure

Check that there are no broken pipes.

 LOW VOLTAGE

Deviation of the supply voltage higher than  

–15% of the plate voltage

Check the supply voltage and the section and 

length of the inverter power cables

HIGH VOLTAGE

Deviation of the supply voltage higher than 

+15% of the plate voltage

Check the supply voltage

OVER TEMP BOX 

(solo T/T)

internal overheating due to overload or exces-

sive ambient temperature

Make sure the air cooling channels are free and 

that the fans are working, check the pump load

•  Check that the inverter has been correctly connected to the power line (which is on)

•  Check that the motor pumps have been correctly connected to the inverter
•  Check that all the cables and connections are operative.

Summary of Contents for 1001905





























Reviews: