EPS 1001905 Operation And Maintenance Manual Download Page 10

10

10

Installation Guide

Information Label on each tank 

Use of drip trays for installations over ceiling height is HIGHLY recommended

  

Customer/installer to check unit for any 

damage or leaks on delivery prior to 

installation of unit

Bunded tank or tank with drip tray 

should be used for in-house installations 

(depending on tank application & location) 

Tank installation above ceiling level is not 

recommended. Unit’s ideal support base 

is concrete due to weight. (i.e. 1L of water 

= 1 kg)

Unit to be fi tted in a safe place away from 

any potential hazards & kept out of direct 

sunlight 

Protective lid of tank to be installed over 

control unit

EPS is unable to service any unit installed 

above ceiling level unless in accordance 

with H&S regulations

Unit to be installed by qualifi ed persons 

only

EPS recommends a by-pass valve be fi tted 

on both the inlet & outlet in the unlikely 

event of a pump failure

Isolation shut-off  valve to be fi tted 

on supply & delivery side of tank (for 

maintenance purposes

DO NOT REMOVE THIS LABEL

(Removal of this label will void warranty) 

Inlet

Overfl ow

By-Pass Line

Typical example of installation 

Rethinking 

Water

The overfl ow pipe that is fi tted should be 

twice the size of the inlet supply minimum (it 

may have to be enlarged further, depending 

on incoming pressure and fl ow) and should 

be piped away to safe drainage zone. (It’s 

recommended that a full test is carried out by 

the installer).

Overfl ow test to be completed after every 

installation. This is to ensure the capacity of the 

overfl ow pipe is able to handle any ballcock 

failure, blockage or restriction. Ensure pipe is 

not restricted & is laid straight with a suffi

  cient 

fall without lags.

The overfl ow pipe must not be obstructed or 

restricted (no sharp elbows), factoring in the 

distance being piped away to the drainage zone.

Overfl ow/vermin screen needs to be cleaned 

regularly to ensure removal of any impurities 

present in the water.

Pressure vessel air pre-charge to be checked 

every 6 months (set 2lbs below cut-in pressure)

High pressure ballcock fi tted as standard. (Low 

range available on request)

EPS recommends testing water for any 

impurities or any water treatment required

EPS accept no responsibility whatsoever for leaks 

inside /outside of tank which are outside of our 

control

ASSEMBLED BY:

DATE:

INSTALLED BY:

DATE:

TEL:

MULTI

BOOST

Scan for O&M Manual 
or download on 
Multiboost.ie

Scan for Multiboost O&M Manual

or download at Multiboost.ie

Fitting of a bypass unit & drip tray 

with correct overflow capability is 

highly recommended

Full overflow test

 

is necessary 

on 

every installation
Use of sharp elbows that may cause 

flow restrictions is not recommended

The

MULTI

BOOST

Range

C

M

Y

CM

MY

CY

CMY

K

Multiboost Stickers 4.pdf   1   08/02/2019   16:36:01

Water 

Supply

Water 

Delivery

Summary of Contents for 1001905





























Reviews: