manualshive.com logo in svg

ePropulsion Pod Drive 1.0 Evo, User Manual, Page: 22 / 48

Share
Download
ePropulsion Pod Drive 1.0 Evo User Manual Download Page 22

20

4.2 Connecting a SPIRIT Battery Plus (Only for Pod Drive 

1.0 Evo)

If you use the Pod Drive 1.0 Evo and SPIRIT Battery Plus at the same time, please fol-
low the steps below to connect SPIRIT Battery Plus and the communication module 
of Pod Drive 1.0 Evo:

1. 

Before connecting the battery and communication module, please fix the battery 

and communication module on the boat.

2. 

Connect the connection cable for Pod 1.0 Evo and Spirit Battery Plus (purchased 
separately) to the power cable of the machine.

3. 

Insert the power cable connector into the battery discharge connector, insert 
the communication cable connector into the connector of the communication 
module (as shown in the figure below), and then tighten the connector clockwise.

Figure 4-3

Do not short-circuit the main switch with other power supplies. The main switch 
should be mounted on the boat, and the back plate of the main switch should 
not be removed.

1

1

2

Summary of Contents for Pod Drive 1.0 Evo

















































Reviews:

No comments