manualshive.com logo in svg

EPOX EP-MVP3C, User Manual, Page: 38 / 63

Share
Download
EPOX EP-MVP3C User Manual Download Page 38

BIOS

EP-MVP3C/2

Page 4-16

Primary Slave UDMA: This allows you to select the mode of operation for the hard
drive.
The default is Auto.

Auto: The computer will select the optimal setting.
Disabled:  The hard drive will run in normal mode.

Secondary Master UDMA: This allows you to select the mode of operation for the
hard drive.
The default is Auto.

Auto: The computer will select the optimal setting.
Disabled:  The hard drive will run in normal mode.

Secondary Slave UDMA: This allows you to select the mode of operation for the
hard drive.
The default is Auto.

Auto: The computer will select the optimal setting.
Disabled:  The hard drive will run in normal mode.

USB Keyboard Support: This controls the activation status of an optional USB
keyboard that may be attached.
The default is disabled.

Enabled: Enable USB keyboard support.
Disabled: Disable USB keyboard support.

Onboard FDD Controller: This controls the state of the onboard floppy controller.
The default value is Enabled.

Enabled: Enable the Onboard Winbond Chips’s floppy drive interface
controller.
Disabled: Disable the Onboard Winbond Chip’s floppy drive interface
controller.

Onboard Serial Port 1: This field allows the user to configure the 1st serial port.
The default is Auto.

AUTO: Enable Onboard Serial port 1 and address is Auto adjusted
COM1: Enable Onboard Serial port 1 and address is 3F8H/IRQ4.

Summary of Contents for EP-MVP3C
































































Reviews:

No comments