background image

page | 14

www.snapav.com   Support 866.838.5052

SPECIFICATIONS

General

Specification

EA-RSP-8D-100

EA-RSP-12D-100

EA-RSP-16D-100

EA-RSP-2D-200

Analog inputs

Stereo RCA inputs

4 pair

6 pair

8 pair

1 pair

Analog loop outputs

Stereo RCA outputs

4 pair

6 pair

8 pair

1 pair

Speaker outputs

8 channels: 4 stereo 

or bridged outputs

12 channels: 6 stereo 

or bridged outputs

16 channels: 8 stereo 

or bridged outputs

2 channels: 1 stereo 

or bridged output

Trigger control

1 x 3.5 mm (in, 4.5V-12V DC), 1 x 3.5 mm (out,12V DC)

Trigger voltage range 

(external)

4.5V-12V DC

IR control

1 x 3.5 mm (in), 1 x 3.5 mm (out)

IR power

+12V pr12V DC to power an IR receiver unit, on/off selectable

IR voltage range

2V-12V

Audio specifications

Specification

EA-RSP-8D-100

EA-RSP-12D-100

EA-RSP-16D-100

EA-RSP-2D-200

Frequency response

20 Hz to 20 kHz, ±2 dB at 1/8 power

Subwoofer output frequency band

20 Hz to 200 Hz, fixed - biquad low-pass filter at 200 Hz, 6 dB/octave slope

Analog loop outputs

Output 2 Vrms at 10K ohm impedance load

Power output @ 8

Ω

, 2 channels driven

2x50W 1 kHz

2 × 100W 1 kHz

Power output @ 4

Ω

, 2 channels driven

2x100W 1 kHz

2 × 200W 1 kHz

Power output @ 8

Ω

, all channels driven

8x50W 1 KHz

12x50W 1 kHz

16x50W 1 kHz

2 × 100W 1 kHz

Power output @ 4

Ω

, all channels driven

8x100W 1 KHz

12x85W 1 kHz

16x80W 1 kHz

2 × 200W 1 kHz

Power output bridged @ 8

Ω

4x200W 1 KHz

6x170W 1 kHz

8x160W 1 kHz

1 × 400W 1 kHz

Minimum impedence

2 ohm

1 ohm

Auto sensing sensitivity

2.5 mVrms

Input sensitivity

1 Vrms

Input impedance

RCA analog input: 20kΩ

RCA analog input: 

22kΩ

Input gain control

Compensate for wide range of sources input levels from 0.5 Vrms to 4 Vrms

Total harmonic distortion @1W, 1 kHz

<0.05%

Total harmonic distortion @50W, 1 kHz

1%

1% @ 100W

Signal-to-noise ratio

>95 dB A-weighted @ rated power

Frequency response

20 Hz - 20 kHz < ± 2 dB

Crosstalk

< -60 dB @ all channels

Dynamic range: S/N ratio

> 100 dB A-weighted @ rated power

THD

0.01% 1 kHz @1/8 rated power 4Ω or 8Ω

0.01% 1 kHz @1/8 

rated power 4Ω 

or 8Ω

www.snapav.com   Support 866.838.5052

Summary of Contents for EA-RSP-12D-100

















Reviews: