background image

C. End Panels – don’t attach to Grid Frames but rather attach to worksurfaces with L” Brackets.  In

this application a Grid Frame straight or T-leg is NOT NEEDED in the end of Grid Frame runs.  The
Grid Frame is held up by a tether bracket that attaches the worksurface to the Frame (tether
brackets are described later in this manual).

D. O-Legs - don’t attach to Grid Frames but rather attach to worksurfaces.  In this application a Grid

Frame straight or T-leg is NOT NEEDED in the end of Grid Frame runs.  The Grid Frame is held up
by a tether bracket that attaches the worksurface to the Frame (tether brackets are described
later in this manual).

Note:  Prior to setting up Grid Frames, note where power and data will be fed up through leg(s), 
whether at the end or in the middle of a run.  Make sure to install legs with power infeed holes 
into Grid Frames at appropriate locations. 

Assembly 

1)

Identify from the labeled cartons the End of Run Frames and unpack these frames first.  Turn

the Frames 

upside down 

to attach the legs.  Take care that legs are inset 6” from Finished End

(end with no holes) as shown below, using a Phillips Head drive to assemble the 2” screws (P/N
UZBOLTU) and 10-24 weld nuts (UZWNUTA).   The Legs are mounted 6” inboard at the end of a
run and when starting a 90 or 120 run of Frames.  See pictures below of assembly process and
final product.

Summary of Contents for Grid Frame















Reviews: