manualshive.com logo in svg

Entrematic LCU40H, Installation Manual, Page: 27 / 46

Share
Download
Entrematic LCU40H Installation Manual Download Page 27

27

IP2246EN

Display

Description

Selections  

available

OC - Obstacle detection limit during closure [%]

Indicates the percentage of the distance travelled during 

 →  

  or after the detection of the closing limit switch 

 

 → 

  → 

  on which the reversal is deactivated.

NB: not active if  

 → 

 → 

 and if 

 → 

 → 

 .

99

TO - Setting motor 2 opening delay time [s]

Adjustment, in seconds, of the delay time for starting
the operation of motor 2, in relation to motor 1.

03

LR - Electric lock release time [s]

If enabled, this indicates the electric lock activation time at the start 
of every opening operation with the automation closed.

1.5

M1 - Operation time - motor 1 [s]

Adjustment, in seconds, of the total operation time for motor 1.

i

WARNING: it is set with a sensitivity interval of 0.5 s, shown 
when the decimal point on the right lights up.

Example: 

 = 7 seconds  /   

 = 7.5 seconds

NB: the setting of 

  is only active with 

 → 

 → 

 .

10

M2 - Operation time - motor 2 [s]

Adjustment, in seconds, of the total operation time for motor 1.

i

WARNING: it is set with a sensitivity interval of 0.5 s, shown 
when the decimal point on the right lights up.

Example: 

 = 7 seconds  /   

 = 7.5 seconds

NB: the setting of 

  is only active with 

 → 

 → 

 .

10

EO - Function of output -LK+
00

 - courtesy light

01

 - electric lock

02

 - electric lock + release stroke

03

 - output active with automation closed (for electromagnets of the fail-safe type)

04

 - output active with automation open

05

 - output active with automation moving (can also be used for electromagnets that need 

to be powered throughout the operation)

06

 - output active with automation opening

07 

 - output active with automation closing

08

 - output active with maintenance alarm triggered

09

 - output active for indicating batteries almost flat

10

 - ON-OFF flashing light for LED without oscillator

11

 - ON-OFF flashing light

ON

 - output always active

FF - Function of LP- 
00

 - courtesy light

01 

 - ON-OFF flashing light

02

 - fixed light with internal oscillator

03 

 - output active with automation closed

04

 - output active with automation open

05 

 - output active with automation moving

06

 - output active with automation opening

07 

 - output active with automation closing

08

 - output active with maintenance alarm triggered

09

 - output active for indicating batteries almost flat

10

 - ON-OFF flashing light for LED without oscillator

11 

 - electric lock

12 

 - electric lock + release stroke

ON

 - output always active

BA

Summary of Contents for LCU40H















































Reviews:

No comments