Completing the Installation
Matrix DFE-Platinum Series Module Installation Guide 3-17
Completing the Installation of a New System
In
a
new
system
of
DFE
‐
Diamond
modules,
one
of
the
installed
DFE
‐
Diamond
modules
will
become
the
management
module
on
chassis
power
up,
and
all
DFE
‐
Diamond
modules
will
automatically
be
set
to
the
factory
default
values.
A
complete
list
of
the
factory
default
values
are
provided
in
Chapter
3
of
the
Enterasys
Matrix
DFE
‐
Diamond/Platinum
Series
Configuration
Guide
.
After
installing
all
DFE
‐
Diamond
modules
into
the
host
chassis
and
making
the
connections
to
the
network,
proceed
to
the
following
“
First
‐
Time
Log
‐
In
Using
a
Console
Port
Connection
”
procedure
to
access
the
module
management
startup
screen
from
your
PC,
terminal,
or
modem
connection.
First-Time Log-In Using a Console Port Connection
Start
the
Command
Line
Interface
(CLI)
from
the
module’s
local
console
port
as
follows:
1.
Connect
a
terminal
to
the
local
console
port
as
described
in
“
Connecting
to
COM
Port
for
Local
Management
”
on
page 3
‐
11.
The
startup
screen,
Figure 3
‐
8
,
displays.
2.
At
the
login
prompt,
enter
one
of
the
following
default
user
names:
–
ro
for
Read
‐
Only
access,
–
rw
for
Read
‐
Write
access,
or
–
admin
for
Super
User
access.
(This
access
level
allows
Read
‐
Write
access
to
all
modifiable
parameters,
including
user
accounts.)
3.
Press
ENTER.
4.
The
Password
prompt
displays.
Leave
this
string
blank
and
press
ENTER.
The
module
information
and
Matrix
prompt
displays
as
shown
in
Figure 3
‐
8
.
The
DFE
‐
Diamond
module
is
now
ready
to
be
configured.
For
information
about
setting
the
IP
address
and
configuring
Telnet
settings
for
remote
access
to
DFE
management,
refer
to
Chapter
3
in
the
Enterasys
Matrix
DFE
‐
Diamond/Platinum
Series
Configuration
Guide
.
The
CLI
commands
enable
you
to
initially
set
up
and
perform
more
involved
management
configurations.
The
Enterasys
Matrix
DFE
‐
Diamond/Platinum
Series
Configuration
Guide
is
available
online
at:
http://www.enterasys.com/support/manuals
If
you
require
assistance,
contact
Enterasys
Networks
using
one
of
the
methods
described
in
“
Getting
Help
”
on
page xiv.
Note:
This procedure applies only to initial log-in, and to logging in to a device not yet configured
with administratively-supplied user and password settings.
By default, the Matrix DFE Series device is configured with three user login accounts:
ro
for Read-
Only access;
rw
for Read-Write access; and
admin
for super-user access to all modifiable
parameters. The default password is set to blank (press ENTER). For information on changing
these default passwords, refer to Chapter 3 in the
Enterasys Matrix DFE-Diamond/Platinum Series
Configuration Guide
.
Summary of Contents for Enterasys Diamond Distributed Forwarding Engine 7KR4297-02
Page 2: ......
Page 42: ...Completing the Installation 3 20 Installation ...
Page 50: ...Overview of DFE Diamond Module Shutdown Procedure 4 8 Troubleshooting ...
Page 64: ...Index 2 ...
