Ensemble Designs Avenue 7910 Manual Download Page 42 | Manualshive

Page: 42 / 43

background image

Model 7910 HD Upconverter And Cross Converter

SPECIFICATIONS

7910 HD Upconverter

Serial Digital Input:

Number:

One

Signal Type:

SD Serial Digital 270 Mb/s
SMPTE 259M
(both 525 and 625 SD standards)
HD Serial Digital 1.485 Gb/s
SMPTE 274M, 292M, or 296M

Impedance:

75 Ω, BNC

Return Loss:

>15 dB

Maximum Cable
Length:
270 Mb/s

300 meters (Belden 1694A or equivalent)

1.485 Gb/s

100 meters (Belden 1694A or equivalent)

Serial Digital Output

Number:

Four

Type:

HD Serial Digital 1.485 Gb/s
SMPTE 274M or 296M

Impedance:

75 Ω, BNC

Return Loss:

>15 dB

Output DC:

None (AC coupled)

HD Standards Supported

1080i (SMPTE 274M -4,5,6) 50, 59.94, 60 Hz
720p (SMPTE 296M -1,2,3) 50, 59.94, 60Hz
1080p (SMPTE 274M -9,10,11) 23.98, 24, 25 Hz
1080sF (RP211 -14,15,16) 23.98, 24, 25 Hz

Reference Input

Number:

One external (module’s BNC)
One internal (frame master ref BNC)

Signal Type:

PAL or NTSC composite video
or HD Tri-Level Sync
SMPTE 274M or 296M

Return Loss:

>40 dB (applies to external ref input)

Conversion Directions

Upconversion between:
525 (NTSC) and 1080i/59.94, 720p/59.94, 1080p/23.98, 1080sF/23.98
625 (PAL) and 1080i/50, 720p/50, 1080p/25, 1080sF/25

Cross Conversion within frame rate families:
525 Derived Family: 1080i/59.94, 720p/59.94, 1080p/23.98, and 1080sF/23.98
625 Derived Family: 1080i/50, 720p/50, 1080p/25, 1080sF/25

7910-42

«
...
40
41
42
43
»

Summary of Contents for Avenue 7910












































Reviews:

No comments

Related manuals for Avenue 7910

Brand: B&B Electronics Pages: 73

Brand: B&B Electronics Pages: 4

Brand: Barco Pages: 8

Brand: Barco Pages: 3

Brand: Barco Pages: 61

Brand: Fema Pages: 28

blueplanet 15.0 TL3

Brand: Kaco Pages: 188

Brand: Kaiser Baas Pages: 3

Brand: RGBlink Pages: 46

Brand: Patton electronics Pages: 2

VARIOMAT 2 11MM

Brand: Calpeda Pages: 64

GlobeTrotter Ex GE 0003

Brand: Option Audio Pages: 4

Brand: CLOCKWORK COMPONENTS Pages: 3

Brand: Daewoo Pages: 16

Brand: GIESELER Pages: 4

Brand: Power Bright Pages: 28

Brand: Samlexpower Pages: 20

Brand: Extron electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands