Ensemble Designs Avenue 7910 Manual Download Page 17

Page: 17 / 43

Model 7910 HD Upconverter And Cross Converter

When

Manual

is selected in the

Mode

menu above, the

Manual

menu shown below will

become active. Set the aspect ratio of the upconverted HD output as desired with the
following controls:

•

Width

– set the aspect ratio width.

•

Height

– set the aspect ratio height.

•

Hor Position

– set the horizontal position of the output.

•

Ver Position

– set the vertical position of the output.

Use the

Default

button in each control to return to the default value.

Use the

Config

menu below to enable the following controls:

•

Noise Reduce

– adjusts the amount of noise reduction on the output signal from

Off

Low

Medium

, or

High

. The typical setting for this parameter is

Off

Low

•

Detail

– adjusts the amount of picture detail enhancement on the output from

Low

Medium

, or

High

. The typical setting for this parameter is

Off

Low

•

3:2 Detect

– turns the control to detect video that has been converted from film,

Off

. Use this only for film applications. The typical setting for this

parameter is

Off

7910-17

Summary of Contents for Avenue 7910












































Search results

Summary of Contents for Avenue 7910

Reviews:

Related manuals for Avenue 7910

Brands by name

Popular brands

Ensemble Designs Avenue 7910, Manual

Search results

Summary of Contents for Avenue 7910

Reviews:

Related manuals for Avenue 7910

Brands by name

Popular brands