background image

Enerdrive ePRO COMBI Owners Manual

Page 4

1. INTRODUCTION

Thank you for purchasing the Enerdrive ePRO Combi inverter/charger combination. Please read this owner’s 
manual for information about using the product correctly and safely. Keep this owner’s manual and all other 
included documentation close to the product for future reference. At the time of this writing, Enerdrive cannot 
guarantee that all mentioned features in this manual are actually available in your ePRO Combi. Nor can 
Enerdrive guarantee that all features are mentioned in this manual. For the most recent manual revision, please 
check the downloads section on our website.

The purpose of this owner’s manual is to provide explanations and procedures for operating, and configuring 
the ePRO Combi. For installing the ePRO Combi, a separate installation guide is included. The installation 
guide is intended for installers that should have knowledge and experience in installing electrical equipment, 
knowledge of the applicable installation codes, and awareness of the hazards involved in performing electrical 
work and how to reduce those hazards.

IMPORTANT SAFETY INFORMATION

This section contains important safety information for the Enerdrive ePRO Combi. Each time, before using 

the Enerdrive ePRO Combi, READ ALL instructions and cautionary markings on or provided with the inverter, 

and all appropriate sections of this guide. The Enerdrive ePRO Combi contains no user serviceable parts. See 

Warranty section for how to handle product issues.

WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN DEATH 

OR SERIOUS INJURY

When working with electrical equipment or lead acid batteries, have someone nearby in case of an 

emergency.

Study and follow all the battery manufacturer’s specific precautions when installing, using and servicing the 

battery connected to the inverter. 

Wear eye protection and gloves.

Avoid touching your eyes while using this unit.

Keep fresh water and soap on hand in the event battery acid comes in contact with eyes. If this occurs, 

cleanse right away with soap and water for a minimum of 15 minutes and seek medical attention.

Batteries produce explosive gases. DO NOT smoke or have an open spark or fire near the system.

Keep unit away from moist or damp areas.

Avoid dropping any metal tool or object on the battery. Doing so could create a spark or short circuit which 

goes through the battery or another electrical tool that may create an explosion.

WARNING: FIRE AND/OR CHEMICAL BURN HAZARD 

Do not cover or obstruct any air vent openings and/or install in a zero-clearance compartment.

Summary of Contents for ePRO Combi

























Reviews: