background image

 WARNING

FAILURE TO FOLLOW THESE INSTRUCTIONS CAN 

RESULT IN DEATH OR SERIOUS INJURY 

•  When working with electrical equipment or lead acid batteries, have someone nearby in case of an 

emergency.

• 

servicing the battery connected to the charger. 

•  Wear eye protection and gloves.
•  Avoid touching your eyes while using this unit.
•  Keep fresh water and soap on hand in the event battery acid comes in contact with eyes. If this occurs, 

cleanse right away with soap and water for a minimum of 15 minutes and seek medical attention.

• 
•  Never attempt to re-charge a damaged, frozen or non-rechargeable battery.
•  Keep unit away from moist or damp areas.
•  Avoid dropping any metal tool or object on the battery. Doing so could create a spark or short circuit 

which goes through the battery or another electrical tool that may create an explosion.

•  Battery charger must be plugged in to an earthed and Australian Standards compliant mains supply. 

If the units power cable is damaged, replace the cable immediately. 

 LIMITATIONS OF USE

•  Do not use in connection with life support systems or other medical equipment or devices. 
•  Charger is not to be used by persons with reduced physical or mental capabilities or lack of knowledge 

and experience. Not to be operated or used by children.

Enerdrive ePOWER Industrial Battery Charger Owner’s Manual (Rev. 1.4)

Page 6

Summary of Contents for ePower Industrial EPI-2430




















Reviews: