background image

1. INTRODUCTION

Thank you for purchasing the Enerdrive ePOWER Industrial Battery Charger. With our state 

Please read and follow these instructions and precautions carefully.

IMPORTANT SAFETY INFORMATION:

This  section  contains  important  safety  information  for  the  Enerdrive  ePOWER  Industrial 
Battery Charger. Each time, before using the Enerdrive ePOWER Industrial Battery Charger, 
READ  ALL  instructions  and  cautionary  markings  on  or  provided  with  the  battery  charger, 
and all appropriate sections of this guide. The Enerdrive ePOWER Industrial Battery Charger 
contains no user serviceable parts. Opening up the charger will void product warranty. See 
Warranty section for how to handle product issues.

 WARNING

FIRE AND/OR CHEMICAL BURN HAZARD 

• 

 WARNING

SHOCK HAZARD. KEEP AWAY FROM CHILDREN!

•  Avoid moisture ingress. Never expose the unit to snow, water, etc.

 WARNING: EXPLOSION HAZARD!

• 

gases (such as gas bottles or large engines).

• 
•  Prolonged contact to high heat or freezing temperatures will decrease the working life of the unit.

Page 5

www.enerdrive.com.au

Summary of Contents for ePower Industrial EPI-2430




















Reviews: