6
ENERCO GROUP, INC. |Indirect Fired Portable Heater
Operating Instructions and Owner’s Manual
TROUBLESHOOTING
Y
D
E
M
E
R
E
S
U
A
C
T
L
U
A
F
D
E
V
R
E
S
B
O
• Check mains
• Check proper positioning and functioning of
•
switch
• Check fuse
• Wrong setting of room thermostat or other
•
control
• Check correct setting of heater control.
•
If thermostat, make sure selected temperature
•
is higher than room temperature
• Thermostat or other control defective
• Replace control device
•
r
o
t
o
m
l
a
c
ir
t
c
e
l
e
e
c
a
l
p
e
R
•
e
v
it
c
e
f
e
d
r
o
t
o
m
l
a
c
ir
t
c
e
l
E
• Electrical motor bearings defective
• Replace electrical motor bearings
• Burned out c
r
e
s
n
e
d
n
o
c
e
c
a
l
p
e
R
•
r
e
s
n
e
d
n
o
• Check connection of H.T. Ieads to electrodes
•
and transformer
• Check electrodes setting (see scheme
•
“REGULATION OF ELECTRODES”)
• Check electrodes for cleanliness
• Replace H.T. transformer
• Flame control box defective
• Replace control box
• Photocell
ll
e
c
o
t
o
h
p
e
c
a
l
p
e
r
r
o
n
a
e
l
C
•
e
v
it
c
e
f
e
d
• Check state of motor-pump plastic coupling
• Check fuel line system including fuel filter for
•
possible leaks
• Clean or replace oil nozzle
• Check electrical connection
• Check thermostat LI
• Clean or replace solenoid
• Make sure air inlet and outlet are free
• Check setting of combustion air flap
• Clean burner disc
p
a
lf
r
i
a
n
o
it
s
u
b
m
o
c
f
o
g
n
it
t
e
s
k
c
e
h
C
•
ri
a
n
o
it
s
u
b
m
o
c
h
c
u
m
o
o
T
•
• Drain fuel in tank with clean fuel
• Clean oil filter
• Air l
r
e
tl
if
l
e
s
e
i
d
e
h
t
d
n
a
s
t
c
u
d
e
h
t
n
o
sl
a
e
s
e
h
t
k
c
e
h
C
•
ti
u
c
ri
c
l
e
u
f
n
i
s
k
a
e
• Check pump pressure
• Clean or replace fuel nozzle
• Check pump pressure
• Replace nozzle
d
i
o
n
e
l
o
s
e
t
e
l
p
m
o
c
r
o
li
o
c
d
i
o
n
e
l
o
s
e
c
a
l
p
e
R
•
e
v
it
c
e
f
e
d
d
i
o
n
e
l
o
S
•
p
o
t
s
t
o
n
s
e
o
d
r
e
t
a
e
H
•
If heater still not working properly, please revert to nearest authorized dealer.
• Not enough c
ombustion air
• Fuel contaminated or contains water
• Not enough fuel at burner
• Too much fuel at burner
• Motor starts, heater emits smoke
• No electrical current
• Motor does not start, no ignition
• Electric ignitor defective
• Not enough or no fuel at all at burner
• Motor starts, no ignition or cuts out
• Solenoid defective
Summary of Contents for 2000ID
