Enduro AS201A, User Manual

Page: 41 / 48

EN
DURO
®
auto Steady 34
Ref: AS201A&B-UM-TKI-0415-Rev. A
Error messages via the remote control handset:
Error messages of the auto Steady system will be communicated via the remote control handset by the green
LED (Fig. 8H), the error message LED’s (Fig. 8L, 8M & 8N) and a buzzer signal:
x
Green LED (Fig. 8H) off, no buzzer: remote control handset is turned off and also system is not activated
x
Green LED (Fig. 8H) continue on, no buzzer: remote control handset is turned on and system is activated
and ready to use.
x
Green LED (Fig. 8H) is blinking, no buzzer: no communication between handset and control unit. This could
be because of too much distance between remote control handset and control unit, or the battery isolation
switch for manoeuvring system is not turned on or that there is a distortion signal disturbing the
communication. As soon as connection is good again the green LED will be continue on and the system is
ready to use.
x
Blue battery voltage LED (Fig. 8N) is blinking in combination with buzzer (2 times blinking, break, 2 times
blinking, break etc.): Battery voltage too low (<10V). Battery needs to be recharged.
x
Blue battery voltage LED (Fig. 8N) is blinking in combination with buzzer (4 times blinking, break, 4 times
blinking, break etc.): Battery Voltage too high (over charged). Try to discharge the battery by turning on a
user (for example a lamp or water-pump).
x
Red overload LED (Fig. 8L) is blinking in combination with buzzer (6 times blinking, break, 6 times blinking,
break etc.): Amp overload protection is activated. Wait about 60 seconds and try again.
x
Blue 9V battery LED (Fig. 8M) is blinking, no buzzer: The internal 9V battery is near empty and needs to be
replaced.
Changing batteries in the remote control handset:
When the internal battery is empty (blue LED (Fig. 8M) is blinking 2Hz), it needs to be replaced.
x
Open the rear cover of the remote control (Fig. 9A).
x
Take out the old battery and dispose in the appropriate way.
x
Install a new replacement battery (Fig. 10). Make sure to use a leak proof PP3 (9Volt) battery (No claims
under guarantee can be considered for damage caused by leaking batteries).
x
Close the rear cover again.
Dead and used batteries may leak and damage the remote control! Remove the batteries if the remote control
is not going to be used for an extended period.
How to synchronise the remote handset with a new manoeuvring system or auto Steady control unit:
The remote control handset and the auto Steady control unit are synchronised with each other in the factory. If
the control unit or the remote control handset is replaced, or the combine-remote handset will also be used for
an EN
DURO
®
caravan manoeuvring system, they must be re-synchronised as described below:
x
Check the installation in accordance with the installation instructions. Check that the battery is properly
connected, check the condition of the battery and that a voltage of 12V is present at the control unit.
x
Please ensure that the battery isolation switch is on.
x
Press the reset button on the control unit:
o
auto Steady system: Press the reset button (Fig. 11D) on the auto Steady control unit for three
seconds and then release it. The green LED (Fig. 11A) starts blinking quickly (2Hz).
o
EN
DURO
®
caravan manoeuvring system: Press the reset button ( see user manual caravan
manoeuvring system ) on the EN
DURO
®
caravan manoeuvring system control unit for three seconds
and then release it. The green LED on the control unit starts blinking quickly (2Hz).
x
Activate the remote control by sliding the slide switch (Fig. 8A) to “On”-I. The green LED of the remote
control and the “UP” and “DOWN” LED’s (Fig. 8R & 8S) will illuminate continuously.
x
Push both the “UP” and “DOWN” buttons (Fig. 8B & 8C) on the remote control at the same time for more
than 3 seconds. Then the handset buzzer will give a short beep to confirm that the synchronisation is
complete.
x
After successful synchronisation, the green LED on the control unit (Fig. 11A) and on the remote control
(Fig. 8H) will illuminate continuously.
After pressing the reset button on the control unit, if have not any operation in more than 15 seconds, the re-
synchronization process will stop.
OPERATION - ELECTRONIC CONTROL UNIT
The electronic control unit (6), which is mounted inside your caravan, is responsible for controlling the
auto Steady system.
The control unit has three LED’s, one pushbutton and one slide switch (Fig. 11):
Green LED (Fig. 11A): Power LED continuously lights up when the system is activated (by moving slide switch
of the remote control to “On”-I). If the remote control is far away from the control unit, beyond the availably
distance, this LED will start blinking.
Blue LED (Fig. 11B): Error message LED concerning caravan battery:
x
Blue LED is blinking (2 times blinking, break, 2 times blinking, break etc.): Battery voltage too low (<10V).
Battery needs to be recharged.