Enduro AS201A, User Manual

Page: 42 / 48

EN
DURO
®
auto Steady 35
Ref: AS201A&B-UM-TKI-0415-Rev. A
x
Blue LED is blinking (4 times blinking, break, 4 times blinking, break etc.): Battery Voltage too high (over
charged). Try to discharge the battery by turning on a user (for example a lamp or water-pump).
Red LED (Fig. 11C) is blinking (6 times blinking, break, 6 times blinking, break etc.): Amp overload protection
is activated. Maybe the system has a current-shortage. Please check the whole system carefully. Wait about 60
seconds and try again.
In general all error messages will reset automatically after one minute. If this is not the case, reset the
electronics by switching off the system via the isolation switch and the remote control for at least 15 seconds
and then turning it on again.
The Reset Button (Fig. 11D): The remote control handset and the control unit are synchronised with each
other in the factory. If the control unit or the remote control handset is replaced, they must be re-synchronised
as described in chapter
OPERATION - REMOTE CONTROL HANDSET: “How to synchronise the remote
handset with a new manoeuvring system or auto Steady control unit”
Jack-up force switch (Fig. 11E): The system is suitable for a big range of the caravans. To make sure that
the system is always working properly and your caravan is stable, the Current-protection can be adjusted via a
slide switch on the control unit (Fig. 11E):
L : Low current for caravans up to 1000kg
M : Normal current for caravans in the range of about 1000 – 1500kg
H : High current for caravans in the range of about 1500 – 2000kg
Different caravan chassis or floors have different situation for jack-up force. The above mentioned values are
just a rough indication. Please check what is the most convenient for your caravan so your caravan or caravan
chassis will not be damaged but still your caravan is stable.
OPERATION - GETTING STARTED
Please make sure you read the safety instructions very carefully and make sure that you
follow these guidelines!
Make sure that the battery that supplies the system is fully charged and in good condition.
Make sure that the caravan is free from the vehicle and the handbrake is on.
Before you can start using the auto Steady system, please make sure you caravan is already levelled out in all
directions. Please use the supplied tool (3) and accomplish this the usual way.
Just as the standard corner steady of your caravan can only be used for stabilising, also the
auto
Steady system cannot be used for jacking up or levelling out your caravan.
Once the caravan is levelled out, you can start using the auto Steady system.
Turn on the battery power isolation switch (23).
Activate the auto Steady system by moving the slide switch to “On”-I on the remote control (Fig. 8A). The
green LED (Fig. 8H) will illuminate continuously. The system is ready for use.
During the operation of the system, the handbrake must be secured.
First check if the slide switch (Fig. 8O) is in “ auto Steady” mode (Fig. 8Q).
Press for at least three seconds the “AUTO DOWN” button (Fig. 8J) with two hands at the same time. The blue
LED (Fig. 8K) will blink during these three seconds and every second there will be a beep. This is warning you
that the system will be activated.
After these three seconds the auto function will start and the corner steadies will automatically act. The blue
LED (Fig. 8K) on the remote control will illuminate continuously. Now you can release the “AUTO DOWN”
button.
The corner steady will act as following:
x
first the two back corner steadies (Fig. 7B and Fig. 7D) lower
x
then the two front corner steadies (Fig. 7A and Fig. 7C) lower
x
than the back corner steadies (Fig. 7B and Fig. 7D) lower again
x
finally the two front corner steadies (Fig. 7A and Fig. 7C) lower again
After activating the “AUTO DOWN” function, before the corner steadies lower, there maybe have a delay about
3 seconds. If one or more corner steadies are not at the complete draw back position, these corner steady will
be draw back for about 3 seconds first.