Endress+Hauser Proline t-mass T 150 Brief Operating Instructions Download Page 28 | Manualshive

Page: 28 / 48

background image

Electrical connection

Proline t-mass T 150

28

Hauser

Load

0 to 750 Ω, depending on the external supply voltage of the power supply unit

7.1.6

Preparing the measuring device

1. Remove dummy plug if present.
2.

NOTICE!

Insufficient sealing of the housing. Operational reliability of the measuring

device could be defeated. Use suitable cable glands corresponding to the degree of

protection.

If measuring device is delivered without cable glands:
Provide suitable cable gland for corresponding connecting cable.

3. If measuring device is delivered with cable glands:

Observe cable specification .

7.2

Connecting the measuring device

NOTICE

Limitation of electrical safety due to incorrect connection!

‣

SELV/PELV-compliant 24 V DC (18 to 30 V) power supply.

‣

4 to 20 mAHART active

‣

Maximum output values: DC 24V, 22 mA, load0 to 750 Ω

«
...
26
27
28
29
30
...
»

Summary of Contents for Proline t-mass T 150

















































Reviews:

No comments

Related manuals for Proline t-mass T 150

Brand: Banner Pages: 11

Brand: Bante Instruments Pages: 10

Brand: BANTE Pages: 11

Brand: Banner Pages: 14

Brand: Banner Pages: 16

Brand: jenway Pages: 18

Brand: Mahr Pages: 384

Brand: T&D Pages: 2

Brand: T&D Pages: 2

Brand: P3 International Pages: 1

Brand: Jula Pages: 9

LISST-PORTABLE XR

Brand: Sequoia Pages: 41

Brand: BYOGuitar.com Pages: 11

Brand: Siko Pages: 2

Brand: Xtralis Pages: 13

Brand: Tektronix Pages: 124

Brand: SOMFY Pages: 40

Brand: Rhosonics Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands