Endress+Hauser Proline Promag 300 Description Of Device Parameters Download Page 31

Page: 31 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

Options

Description

Check not done

The device configuration of the HistoROM has not yet been compared to the
backup copy in the device memory.

Dataset incomp.

The backup copy in the device memory is not compatible with the device.

HistoROM

A HistoROM is a "non-volatile" device memory in the form of an EEPROM.

3.1.3

"Diagn. handling" submenu

Navigation

 Expert → System → Diagn. handling

‣

Diagn. handling

Alarm delay (0651)

→  31

‣

Diagn. behavior

→  32

Alarm delay



Navigation

 Expert → System → Diagn. handling → Alarm delay (0651)

Description

Use this function to enter the time interval until the device generates a diagnostic

message.

The diagnostic message is reset without a time delay.

User entry

0 to 60 s

Factory setting

0 s

Additional information

Result

This setting affects the following diagnostic messages:

• 170 coil resistance

• 832 Electronic temp.

• 833 Electronic temp.

• 834 Process temp.

• 835 Process temp.

• 962 empty pipe

Summary of Contents for Proline Promag 300

















































































































































































































































































Search results

Summary of Contents for Proline Promag 300

Reviews:

Related manuals for Proline Promag 300

Brands by name

Popular brands

Endress+Hauser Proline Promag 300, Description Of Device Parameters

Search results

Summary of Contents for Proline Promag 300

Reviews:

Related manuals for Proline Promag 300

Brands by name

Popular brands