Endress+Hauser Proline Promag 300 Description Of Device Parameters Download Page 138

Page: 138 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

138

Hauser

Additional information

User interface

• Open

The switch output is not conductive.

• Closed

The switch output is conductive.

Invert outp.sig.



Navigation

 Expert → Output → PFS output 1 to n → Invert outp.sig. (0470–1 to n)

Description

Use this function to select whether to invert the output signal.

Selection

• No

• Yes

Factory setting

Additional information

Selection

option (passive - negative)

A0026693

Yes

option (passive - positive)

A0026692

3.5.3

"Relay output 1 to n" submenu

Navigation

 Expert → Output → Relay output 1 to n

‣

Relay output 1 to n

Terminal no.

→  139

Relay outp.func.

→  139

Assign dir.check

→  140

Summary of Contents for Proline Promag 300

















































































































































































































































































Search results

Summary of Contents for Proline Promag 300

Reviews:

Related manuals for Proline Promag 300

Brands by name

Popular brands

Endress+Hauser Proline Promag 300, Description Of Device Parameters

Search results

Summary of Contents for Proline Promag 300

Reviews:

Related manuals for Proline Promag 300

Brands by name

Popular brands