background image

Maintenance

Oxymax H COS21

8

Hauser

4.

Switch-on the transmitter.
If you connect the sensor to the transmitter, polarization is automatically performed after 
switching on the transmitter.

5.

Wait for the polarization time to end.

"

Caution! 
• When you remove the sensor from the medium,  protect the sensor from strong sunlight.
• Make sure you comply with the instructions for commissioning and calibration in the 

Operating Instructions of the transmitter.

4.3

Calibration

Calibrate the sensor (air calibration) immediately after the polarization time has elapsed.

The calibration intervals depend heavily on:
• The application and
• The installation position of the sensor.

The following methods help you determine how long the calibration intervals should be:

1.

Check the sensor one month after its being put into operation by taking it out of the fluid, 
drying it and then measuring the oxygen saturation index at air after 10 minutes.
Decide using the results:

a. If  the  measured  value  is  not  at  102 ± 2 %SAT,  you  have  to  calibrate  the  sensor.

b. Otherwise, double the length of time to the next inspection.

2.

Proceed as per Point 1 after two, four and/or eight months. In this way, you can determine 
the optimum calibration interval for your sensor.

!

Note! 
Be sure to calibrate the sensor at least once a year.

5

Maintenance

Maintenance work must carried out at regular intervals. To ensure that it is carried out, we 
recommend you enter the maintenance dates into an operations logbook or in an 
operations calendar in advance.
The maintenance cycle primarily depends on the system, the installation conditions and the 
medium in which measurement is taking place.

The following activities must be carried out:
• Cleaning the sensor

(In particular when the membrane is soiled)

• Check the measuring function:

1. Remove the sensor from the medium.

Summary of Contents for Oxymax H COS21













Reviews: