Endress+Hauser Micropilot M FMR250 Operating Instructions Manual Download Page 97

Page: 97 / 120

Micropilot M FMR250 FOUNDATION Fieldbus

Technical data

Hauser

10.1.9

Certificates and approvals

CE approval

The measuring system meets the legal requirements of the EC-guidelines. Hauser confirms
the instrument passing the required tests by attaching the CE-mark.

RF approvals

R&TTE, FCC

External standards and
guidelines

EN 60529

Protection class of housing (IP-code).

EN 61010

Safety regulations for electrical devices for measurement, control, regulation and laboratory use.

EN 61326-X

EMC product family standard for electrical equipment for measurement, control and laboratory use.

NAMUR

User Association for Automation in Process Industries.

Summary of Contents for Micropilot M FMR250

























































































































Search results

Summary of Contents for Micropilot M FMR250

Reviews:

Related manuals for Micropilot M FMR250

Brands by name

Popular brands

Endress+Hauser Micropilot M FMR250, Operating Instructions Manual

Search results

Summary of Contents for Micropilot M FMR250

Reviews:

Related manuals for Micropilot M FMR250

Brands by name

Popular brands