Endress+Hauser micropilot M FMR 240 Operating Instructions Manual Download Page 57 | Manualshive

Page: 57 / 112

background image

Micropilot M FMR 240 with PROFIBUS PA

Operation

E Hauser

57

5.5.9

Commuwin II-Operating Programm

Commuwin II is an operating software with graphical support for intelligent transmitters
with the communication protocols Rackbus, Rackbus RS 485, INTENSOR, HART or
PROFIBUS PA. It is compatible with the operating systems Win 3.1/3.11, Win95, Win98
and WinNT4.0. All functions of Commuwin II are supported. The configuration is made
via operating matrix or graphic surface. A envelope curve can be displayed in ToF Tool.

!

Note!
Further information on Commuwin II is given in the following E+H documentation:

•

System Information: SI 018F/00/en “Commuwin II”

•

Operating Manual: BA 124F/00/en “Commuwin II” operating program

Connection

The table provides an overview of the Commuwin connections.

Interface

Hardware

Server

Device list

HART

Commubox FXA 191 to HART
Computer with RS-232C interface

HART

Connected instrument

Interface FXN 672
Gateway for MODBUS, PROFIBUS,
FIP, INTERBUS, etc.

ZA 673 for
PROFIBUS

List of all rack bus modules:
the required FXN 672 must
be selected

Computer with
RS-232C interface or
PROFIBUS card

ZA 672 for
other

«
...
55
56
57
58
59
...
»

Summary of Contents for micropilot M FMR 240

















































































































Reviews:

No comments

Related manuals for micropilot M FMR 240

Brand: Landis+Gyr Pages: 10

Brand: Keller Pages: 8

Trimble Ranger 3

Brand: Badger Meter Pages: 20

Brand: A&D Pages: 38

Brand: D-tect Systems Pages: 28

Brand: Megasat Pages: 25

Brand: Thermocable Pages: 10

Brand: South Pages: 54

Brand: E Instruments Pages: 2

Brand: Lasertec Pages: 28

Brand: janitza Pages: 12

Brand: Fisher Research Labs Pages: 20

Brand: Stageline Pages: 30

Brand: MTC Pages: 32

Brand: Elcometer Pages: 59

Brand: Roland Pages: 32

Brand: Roland Pages: 2

Brand: Agilent Technologies Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands