Endress+Hauser Memosens Wave CAS80E Operating Instructions Manual Download Page 32

Page: 32 / 44

Maintenance

Memosens Wave CAS80E

Hauser

Maintenance

CAUTION

Acid or medium

Risk of injury, damage to clothing and the system!

‣

Switch off the cleaning unit and spectrometer before removing the spectrometer from

the medium.

‣

Wear protective goggles and safety gloves.

‣

Clean away splashes on clothes and other objects.

‣

You must perform maintenance tasks at regular intervals.

We recommend setting the maintenance times in advance in an operations journal or log.
The maintenance cycle primarily depends on the following:

• The system

• The installation conditions

• The medium in which measurement takes place

10.1 Maintenance schedule

Monthly:

Visual inspection, cleaning of the optical windows.

The maintenance intervals depend on the medium. If a cleaning unit is connected, the

maintenance intervals can be extended.

10.2 Maintenance tasks

NOTICE

Dirt on the optical components

‣

Perform maintenance work at a clean workplace.

NOTICE

Work performed carelessly

Damage to the optical components!

‣

Ensure that maintenance work is carried out by qualified specialists only.

10.2.1 Cleaning the spectrometer

Spectrometer fouling can affect the measurement results and even cause a malfunction.
The spectrometer must be cleaned regularly to ensure reliable measurement results. The

frequency and intensity of the cleaning process depend on the medium.
Clean the spectrometer:

• As specified in the maintenance schedule

• Before every calibration

• Before returning it for repairs

Summary of Contents for Memosens Wave CAS80E













































Search results

Summary of Contents for Memosens Wave CAS80E

Reviews:

Related manuals for Memosens Wave CAS80E

Brands by name

Popular brands

Endress+Hauser Memosens Wave CAS80E, Operating Instructions Manual

Search results

Summary of Contents for Memosens Wave CAS80E

Reviews:

Related manuals for Memosens Wave CAS80E

Brands by name

Popular brands