Endress+Hauser Liquiline System CA80TP Brief Operating Instructions Download Page 11

Page: 11 / 48

Liquiline System CA80TP

Installation

Hauser

Installation

CAUTION

Incorrect transportation or installation can cause injury and damage the device

‣

Always use a lifting truck or a fork-lift to transport the analyzer. Two people are needed for

the installation.

‣

Lift the device by the recessed grips.

‣

In the case of the version with the analyzer stand, make sure that the housing is fixed to

the floor.

‣

Check that the analyzer is fully hooked into the wall holder unit at the top and bottom and

secure it to the upper wall holder unit using the securing screw.

4.1

Installation conditions

4.1.1

Installation options

The analyzer can be mounted in three different ways:

• As an independent table-top device

• Mounted on a wall

• Mounted on a base

4.1.2

Dimensions

530 (20.87)

463 (18.23)

793 (31.22)

A0028820

 1

Liquiline System CA80 closed version, dimensions in mm (inch)

Summary of Contents for Liquiline System CA80TP

















































Search results

Summary of Contents for Liquiline System CA80TP

Reviews:

Related manuals for Liquiline System CA80TP

Brands by name

Popular brands

Endress+Hauser Liquiline System CA80TP, Brief Operating Instructions

Search results

Summary of Contents for Liquiline System CA80TP

Reviews:

Related manuals for Liquiline System CA80TP

Brands by name

Popular brands