Endress+Hauser HART Proline t-mass I 300 Operating Instructions Manual Download Page 136

Page: 136 / 202

Diagnostics and troubleshooting

Proline t-mass I 300 HART

136

Hauser

Error

Possible causes

Solution

Device shows correct value on local
display, but signal output is
incorrect, though in the valid range.

Configuration error

Check and correct the parameter
configuration.

Device measures incorrectly.

Configuration error or device is
operated outside the application.

1. Check and correct parameter
configuration.
2. Observe limit values specified in
the "Technical Data".

For access

Error

Possible causes

Solution

No write access to parameters

Hardware write protection enabled

Set the write protection switch on
main electronics module to the

OFF

position →  124.

No write access to parameters

Current user role has limited access
authorization

1. Check user role →  57.
2. Enter correct customer-specific
access code →  57.

No connection via HART protocol

Communication resistor missing or
incorrectly installed.

Communication resistor (250 Ω)
correctly. Observe the maximum
load →  169.

No connection via HART protocol

Commubox
• Connected incorrectly
• Configured incorrectly
• Drivers not installed correctly
• USB interface on computer

configured incorrectly

Observe the documentation for the
Commubox.



FXA195 HART: Document
"Technical Information"
TI00404F

Not connecting to Web server

Web server disabled

Using the "FieldCare" or "DeviceCare"
operating tool, check whether the
web server of the measuring device
is enabled, and enable it if
necessary→  64.

Incorrect setting for the Ethernet
interface of the computer

1. Check the properties of the
Internet protocol (TCP/IP)
→  60→  60.
2. Check the network settings with
the IT manager.

Not connecting to Web server

Incorrect IP address

Check the IP address:
192.168.1.212 →  60→  60

Not connecting to Web server

Incorrect WLAN access data

• Check WLAN network status.
• Log on to the device again using

WLAN access data.

• Verify that WLAN is enabled on

the measuring device and
operating device →  60.

WLAN communication disabled

–

Not connecting to Web server,
FieldCare or DeviceCare

No WLAN network available

• Check if WLAN reception is

present: LED on display module
is lit blue

• Check if WLAN connection is

enabled: LED on display module
flashes blue

• Switch on instrument function.

Network connection not present or
unstable

WLAN network is weak.

• Operating device is outside of

reception range: Check network
status on operating device.

• To improve network

performance, use an external
WLAN antenna.

Summary of Contents for HART Proline t-mass I 300











































































































































































































Search results

Summary of Contents for HART Proline t-mass I 300

Reviews:

Related manuals for HART Proline t-mass I 300

Brands by name

Popular brands

Endress+Hauser HART Proline t-mass I 300, Operating Instructions Manual

Search results

Summary of Contents for HART Proline t-mass I 300

Reviews:

Related manuals for HART Proline t-mass I 300

Brands by name

Popular brands