Endress+Hauser Fieldgate FXA42 Page 30 Operating Instructions Manual Download

Page: 30 / 118

Commissioning

Fieldgate FXA42

Hauser

Configuration of FXA42 as a Modbus TCP client (reading out data from other

systems)

The following examples show how to configure the gateway to read out data using the

Modbus TCP. Please refer to the device documentation for additional information.
Suitable devices are:

• Rapsystems HG1 Plus HART to Modbus gateway (accessory)

• Phoenix Contact GW PL ETH/BASIC-BUS HART Ethernet multiplexer head module

(accessory)

• Datexel DAT8017-I server module, analog to Modbus TCP converter (accessory)
Other devices that can communicate via Modbus TCP can also be connected.

Example with HG1 Plus

1. Open the Settings page .
2. Select the

Modbus client/master

tab.

3. Select

Edit device

and enter the data:



A0035102-EN

4. Select

Edit value

and enter the data. Example: enter Primary Variable (PV) for the

first HART device connected to the HG1 Plus (enable and enter limits if necessary):


A0035103-EN

Summary of Contents for Fieldgate FXA42























































































































Search results

Summary of Contents for Fieldgate FXA42

Reviews:

Related manuals for Fieldgate FXA42

Brands by name

Popular brands

Endress+Hauser Fieldgate FXA42, Operating Instructions Manual

Search results

Summary of Contents for Fieldgate FXA42

Reviews:

Related manuals for Fieldgate FXA42

Brands by name

Popular brands