manualshive.com logo in svg

Endress+Hauser Fieldgate FXA42, Operating Instructions Manual, Page: 93 / 118

Share
Download
Endress+Hauser Fieldgate FXA42 Operating Instructions Manual Download Page 93

Fieldgate FXA42

Operation

Hauser

93

OpenSSL

OpenSSL is used in OpenVPN.
Project website: 

www.openssl.org

License: 

OpenSSL license

OpenVPN

"OpenVPN" is a trademark of OpenVPN Technologies, Inc.
Project website: 

openvpn.net

License: 

OpenVPN licence

8.4.14   DHCP server

The device's firmware features a Dynamic Host Configuration Protocol (DHCP) server

which can be enabled and configured on this page.

The following parameters must be configured for the DHCP server:

• Maximum number of clients to be serviced. The maximum number of clients is 100,

including static mappings.

• Lease time

• Server IP address

• Netmask
The server will lease IP addresses from the particular network (except for its own IP

address). In addition, it is possible to specify a gateway IP address and a name server IP

address that are also distributed.

Static leases

Up to 10 static leases can be configured in this section. A static lease will ensure that a

client with a specific MAC address will be given a predefined IP address and that this IP

address is not leased to another client. The MAC address of the client must be specified

without any delimiters (e.g. 003056A1DB30).

Event log messages

The following section describes the messages that the DHCP server may log to the event

log. The messages are prefixed with the text 

DHCP server

:

Running

The DHCP server has been successfully started.

Added static lease IP=<x>, MAC=<y>

A static lease has been added. The message also shows the IP and MAC address.

Summary of Contents for Fieldgate FXA42























































































































Reviews:

No comments