®
Outdoor Natural Gas Patio Heater Model No. 233010
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
Re-lighting
Note:
For your safety, control knob cannot be turned “OFF” without first depressing control
knob in “PILOT” position and then rotating it to “OFF”.
1. Turn control knob to “OFF”.
2. Wait at least 5 minutes, to let gas dissipate, before attempting to relight pilot.
3. Repeat the “Lighting” steps.
Shut Down
1. Turn control knob clockwise to “PILOT”. (Normally, burner will make a slight popping sound
when extinguished.) Burner will extinguish but pilot will remain “ON”.
2. To extinguish pilot, depress control knob and continue to turn it clockwise to “OFF”.
3. Turn natural gas main valve to “OFF” and disconnect when heater is not in use.
Note: After use, some discoloration of the emitter screen is normal.
Cleaning and Care
Caution
1. All cleaning and maintenance should be done when patio heater is
cool and with the fuel supply disconnected.
2. DO NOT clean any patio heater part in a self cleaning oven. The
extreme heat will damage the finish.
Notices
1. Abrasive cleaners will damage this product.
2. Never use oven cleaner to clean any part of heater.
3. Do not clean any heater part in a self cleaning oven. The extreme heat will damage
the finish.
4. More frequent cleaning may be required as necessary. It is imperative that control
compartment, burners and circulating air passageways of the heater be kept clean.
5. Spiders and insects can create a dangerous condition that may damage heater or
make it unsafe. Keep burner area clean of all spiders, webs, or insects. Clean burner
holes by using a heavy-duty pipe cleaner. Compressed air may help clear away
smaller particles.
6. Inspect heater before each use.
7. Have heater inspected annually and repairs should be made by a qualified service
person.
8. Check heater immediately if any of the following conditions exist:
a. The smell of gas in conjunction with extreme yellow tipping of burner flames.
b. Heater does not reach proper temperature.
c. Heater’s glow is excessively uneven
d. Burner makes popping noises during use.
Note: A slight pop is normal when burner is extinguished.
9. Carbon deposits may create a fire hazard. Keep dome and emitter clean at all times.
10. Do not clean heater with combustible or corrosive cleaners. Use warm, soapy water.
11. Do not paint engine, engine access panel or dome.
12. This heater should be thoroughly cleaned on a regular basis.
13. After a period of storage and/or nonuse, check for leaks, burner obstructions and
inspect for any abrasion, wear, cuts to the hose.
Cleaning Surfaces
1. Wipe surfaces clean with mild dishwashing detergent or baking soda.
2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush.
3. Rinse clean with water.
Note:
While cleaning your unit, be sure to keep the area around the burner and pilot assembly
dry at all times. Do not submerge the control valve assembly. If the gas control is submerged
in water, do NOT use it. It must be replaced.
Annual Maintenance
To enjoy years of outstanding performance from your heater, make sure you perform the
following maintenance activities on a regular basis:
1. Keep exterior surfaces clean.
2. Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean.
Signs of possible blockage include:
Gas odor with extreme yellow tipping of flame.
Heater does NOT reach the desired temperature.
Gas Line Connection
Make 2-3 oz.a of leak solution by mixing one part liquid
dishwashing soap with three parts water.
Make sure control knobs are “OFF”.
Turn natural gas line “ON” at main valve.
Spoon leak check solution at all “x” locations
If any bubbles appear turn natural gas main valve “OFF”,
reconnect and re-test. If you continue to see bubbles
after several attempts, turn natural gas main valve
“OFF”, and contact 1.800.762.1142 for assistance.
If no bubbles appear after one minute turn natural gas
main valve “OFF” wipe away solution and proceed.
Before Lighting
Heater should be thoroughly inspected before each use,
and by a qualified service person at least annually.
If relighting a hot heater, always wait at least 5 minutes.
Inspect the hose assembly for evidence of excessive
abrasion, cuts, or wear. Suspected areas should be
leak tested. If the hose leaks, it must be
replaced prior to operation. Only use the
replacement hose assembly specified by
manufacturer.
Lighting
Note:
this heater is equipped with a pilot
light that allows for safer startups and
shutdowns. Pilot must be lit before main
burner can be started.
1. Turn tank valve “OFF”.
2. Push control knob in and turn to “OFF”.
3. Wait 5 minutes for any gas to clear.
4. Turn tank valve “ON”.
5. Open viewing hole by sliding cover to either
side.
6. Push control knob in and rotate to “PILOT”
position. Keep the control knob depressed.
Note:
for initial start or after any tank change,
hold control knob in for 2 minutes to purge air
from gas lines before proceeding.
7. Push igniter button once. Pilot light flame
will appear and be visible through viewing
hole.
8. Release control knob after 30 seconds. Pilot
light will remain lit. If not, return to step 1.
9. Turn control knob to “HIGH”. Burner will light immediately. Flame is visible through viewing
hole. If not, return to
step 1.
10. If for some reason your ignitor fails to deliver a spark, your heater can be started by
inserting a lit match through the pilot view hole while pushing the control knob in while in
the pilot position.
WARNING
FOR YOUR SAFETY:
Be careful when attempting to manually ignite this heater. Holding in
the control know for more than 10 seconds before igniting the gas will
cause a ball of flame upon ignition.
Have a question or are having problems visit www.bluerhino.com or call 1.800.762.1142.
Note:
the burner may be noisy when initially turned on. To eliminate excessive noise from
the burner, turn the control knob to the pilot position. Then, turn the knob to the level of heat
desired.
When heater is ON:
Emitter screen will become bright red due to intense
heat. The color is more visible at night.
Burner will display tongues of blue and yellow flame.
These flames should not be yellow or produce thick
black smoke, indicating an obstruction of airflow
through the burners. The flame should be blue with
straight yellow tops.
If excessive yellow flame is detected, turn off heater
and visit www.bluerhino.com or call 1.800.762.1142.
Natural Gas Line
X
Natural Gas Connection
View Hole
Control Knob
Operating Instructions (continued)
Proper flame height.
